For low and high current applications with excellent protection against sliding contact
wear. Good protection against nonferrous metal corrosion due to humidity. Applications
include turn signal switches, window lift switches, power seat switches and ignition
switches.

For high current applications requiring low arc switching debris, durability and corrosion
protection for Cu, Cu alloy, Ag, Au and Ni metals. Excellent mechanical stability,
low fluid migration, good mobility at low temperatures and low evaporation at high
temperatures. Applications include transmission neutral start switches and similar high
temperature, low current devices.

For high current applications requiring extended operation at high temperatures, low arc
switching debris, reduced sliding wear and corrosion protection on Cu, Cu alloys, Ag,
Au and Ni metals. Excellent mechanical stability, low fluid migration, and low evaporation
at high temperatures. Good water resistance.

High grade PFPE grease. Low volatility and high oxidation resistance for extended durability
in thin films. Extremely wide operating temperature range. Contains an ultraviolet
reactive tracer.

For on non-arcing, low current sliding switch contacts where a high quality, low volatility
and water washout resistant grease is required. Designed for applications that with
higher contact forces. Reduces wear due to vibration.

High current switching with low arc debris. Inhibited for Cu and Ag corrosion with
enhanced contact antiwear. Also exhibits good mechanical and chemical stability.
Applications include high current switches, potentiometers and similar devices.

Non-melting grease for high current switching with low arc debris. Inhibited for Cu
and Ag corrosion with good mechanical and chemical stability. Applications include
high current switches, potentiometers and similar devices.

NS-4818-G is a ball and roller bearing grease formulated for continuous operation at temperatures above 150°C. Formulated with a per-fluorinated polyether (PFPE) base oil and a lithium complex soap thickerer to provide extreme pressure and antiwear protection as well as corrosion resistance under extreme operating conditions.

NS-3913-G1 is an extreme pressure fortified grease designed for couplings and gears. High film strength components provide long lasting protection. EP and anti-wear additives along with rust inhibitors provide excellent performance for applications ranging from aerospace such as helicopter drive shaft couplings and bearings to industrial applications such as steel mill gear couplings. NS-3913-G1 is the only lubricant approved by Bell Helicopter Textron for use on their Crown Gear Driveshaft couplings.

NS-6075-G is a versatile extreme pressure and anti-wear lubricant. This lubricant contains a petroleum base oil and inorganic thickener that gives the grease the ability to lubricate effectively at temperatures above 450°F. Formulated with a unique combination of molybdenum disulfide and graphite which gives NS-6075-G the ability to lubricate even when wiped to a thin film, providing metal surfaces protection during periods of high speeds, high loads and extreme pressure. It also provides excellent water resistance, rust and oxidation resistance, good mechanical stability, adhesiveness and pumpability.
 

A tacky assembly aid to "stick-hold" parts together in mechanisms such as gear boxes, pumps, and engine accessories. NS-6074-F is also used to "wet out" or lubricate O-rings prior to pressing them into cavities, preventing chafing or tearing of O-ring surface.

NS-5806-G is a non-melting extreme pressure grease designed for lubrication of aircraft slides and bearings. Fortified with molybdenum disulfide for excellent protection of sliding steel on steel against wear and seizure. Gelled with a non-melting bentonite thickener for extended operation at high temperature.
 

A high capacity semi-fluid grease designed for high performance applications. This product exhibits a wide operating temperature lubricant with extreme pressure and antiwear properties. Extreme stability under high centrifugal conditions. Possible applications might include couplings, gear boxes and bearings. This product does not contain solids or silicone. NS-4405-FG is the only lubricant approved by McDonnell Douglas for use on the Intermediate and Tail Rotor gear boxes on the AH-64 Apache helicopter gun ship.

NS-1822-G was formulated as a multi-purpose aircraft airframe grease for highly loaded bearings, gears and actuator screws. A low viscosity synthetic ester base fluid and a non-melting thickener system enable excellent low-temperature mobility and pumpability providing very low starting and running torque values. Good resistance to moisture as well as enhanced protection against both ferrous and non-ferrous metal rust and corrosion make this product a natural for use in marine environments.

NS-1822-G is a clay thickened grease approved under MIL-PRF-23827C Type II. NS-1822-G should not be mixed with soap based greases approved under MIL-PRF-23827C Type I

Medium viscosity EP/antiwear grease designed to be resistant to hexane solvent washout. It is not compatible with most mineral oil and synthetic greases. Non-melting thickener. NSF H1.

For high current applications requiring low arc switching debris, durability and corrosion
protection for Cu, Cu alloy, Ag, Au and Ni metals. Excellent mechanical stability,
low fluid migration, good mobility at low temperatures and low evaporation at high
temperatures. Applications include transmission neutral start switches and similar high
temperature, low current devices.

For high current applications requiring extended operation at high temperatures, low arc
switching debris, reduced sliding wear and corrosion protection on Cu, Cu alloys, Ag,
Au and Ni metals. Excellent mechanical stability, low fluid migration, and low evaporation
at high temperatures. Good water resistance.

High grade PFPE grease. Low volatility and high oxidation resistance for extended durability
in thin films. Extremely wide operating temperature range. Contains an ultraviolet
reactive tracer.

For on non-arcing, low current sliding switch contacts where a high quality, low volatility
and water washout resistant grease is required. Designed for applications that with
higher contact forces. Reduces wear due to vibration.

High current switching with low arc debris. Inhibited for Cu and Ag corrosion with
enhanced contact antiwear. Also exhibits good mechanical and chemical stability.
Applications include high current switches, potentiometers and similar devices.

Non-melting grease for high current switching with low arc debris. Inhibited for Cu
and Ag corrosion with good mechanical and chemical stability. Applications include
high current switches, potentiometers and similar devices.

A fully synthetic NLGI 2 grease formulated to provide friction reduction, antiwear and mild EP protection with premium corrosion protection for gears and bearings. A high viscosity index PAO base fluid provides low drag lubrication at lower operating temperatures. Its shear resistant calcium sulfonate complex thickener system provides a consistent lubrication film and is extremely resistant to moisture, humidity and steam.

NS-1514-G is a food grade synthetic hydrocarbon based grease with a calcium sulfonate complex thickener. This product provides load carrying performance and reduced component wear. This grease also has excellent corrosion protection and superior water washout and spray off properties for bearings and gears.
 

For low and high current applications with excellent protection against sliding contact
wear. Good protection against nonferrous metal corrosion due to humidity. Applications
include turn signal switches, window lift switches, power seat switches and ignition
switches.

Designed for use in mechanical sections of switches, small mechanisms and low to medium load gearboxes. This product exhibits high mechanical stability, wide operating temperature range and excellent oxidation and thermal stability. Exceptional 'smooth feel' and mechanical damping are additional characteristics. PTFE enhanced.
 

A synthetic grease designed for use as a mechanical lubricant as well as an electrical contact interface lubricant. This product is suitable for low current (milliamp) and high current applications requiring low arcswitching debris, durability, and non-ferrous (e.g. Copper, Brass, Silver) corrosion protection over a range of -40°C to +149°C (-40°F to +300°F). NS-396-G exhibits excellent mechanical stability and low fluid migration with low evaporation at high temperatures. Lower mechanical friction and improved anti-wear at higher temperatures is also exhibited. May be used in switches, small gearboxes, wiper motors, cables and other similar devices.

NS-1302-G was designed to provide smooth feel to plastic-plastic and plastic-metal sliding interfaces. The use of a high performance viscosity modifier combined with a low viscosity base fluid allows for excellent low temperature use with good high temperature damping ability. This product exhibits excellent mechanical stability and extremely low fluid migration, with low evaporation at high temperatures. Lower mechanical friction and improved anti-wear at higher temperatures are also exhibited. May be used in mechanical sections of switches, small gearboxes, wiper motors, cables and other similar devices.

Non-melting grease for high current switching with low arc debris. Inhibited for Cu
and Ag corrosion with good mechanical and chemical stability. Applications include
high current switches, potentiometers and similar devices.

For on non-arcing, low current sliding switch contacts where a high quality, low volatility
and water washout resistant grease is required. Designed for applications that with
higher contact forces. Reduces wear due to vibration.

High grade PFPE grease. Low volatility and high oxidation resistance for extended durability
in thin films. Extremely wide operating temperature range. Contains an ultraviolet
reactive tracer.

For high current applications requiring extended operation at high temperatures, low arc
switching debris, reduced sliding wear and corrosion protection on Cu, Cu alloys, Ag,
Au and Ni metals. Excellent mechanical stability, low fluid migration, and low evaporation
at high temperatures. Good water resistance.

For high current applications requiring low arc switching debris, durability and corrosion
protection for Cu, Cu alloy, Ag, Au and Ni metals. Excellent mechanical stability,
low fluid migration, good mobility at low temperatures and low evaporation at high
temperatures. Applications include transmission neutral start switches and similar high
temperature, low current devices.

For low and high current applications with excellent protection against sliding contact
wear. Good protection against nonferrous metal corrosion due to humidity. Applications
include turn signal switches, window lift switches, power seat switches and ignition
switches.

NS-7502-GA is a non-hydrocarbon electrical contact lubricant designed to prevent contact wear and corrosion for contacts with higher then normal loading. This product has outstanding performance in applications requiring low arc-switching debris, durability, and lubricating qualities over a wide temperature range of -40°C to 140°C.  Inhibited for Cu and Ag corrosion, and exhibits good mechanical stability.

NS-4200-G was formulated to lubricate high and low current sliding electrical contacts. This product exhibits outstanding dry and high humidity nonferrous metal corrosion protection and an operating temperature range of -55°F(-67°C) to +225°F(107°C). It's soft consistency enables a constant lubricating film for high duty cycle switches. Applications include switch contacts and light duty mechanical interfaces.

NS-4818-G is a ball and roller bearing grease formulated for continuous operation at temperatures above 150°C. Formulated with a per-fluorinated polyether (PFPE) base oil and a lithium complex soap thickerer to provide extreme pressure and antiwear protection as well as corrosion resistance under extreme operating conditions.

A medium viscosity silicone based grease with very good water resistance. Contains PTFE for enhanced friction reduction. Excellent plastic and elastomer lubrication capabilities. Low volatility provides for a long service life.

A low viscosity silicone grease formulated with PTFE for applications requiring damping, stick-slip reduction and noise control properties. High mechanical stability, low migration and oil separation, multi-plastics compatibility and wide operating temperature range are additional features of this product. Excellent anti-wear for plastic on plastic or metal on plastic interfaces.

A synthetic hydrocarbon based grease that provides smooth feel to plastic on plastic and plastic on metal sliding interfaces while providing corrosion protection for nonferrous metals. The use of a high performance viscosity modifier combined with a low viscosity base fluid allows for excellent low temperature use with good high temperature damping ability. This product exhibits excellent mechanical stability and extremely low fluid migration, with low evaporation at high temperatures. Lower mechanical friction and anti-wear at higher temperatures are also exhibited.

A fully synthetic grease designed for use in both mechanical and electrical interfaces. This product was formulated to reduce friction and wear on low current (<0.5 amp) sliding electrical contacts. It provides corrosion protection for non-ferrous metals such as copper and silver over a temperature range of -40°C to +121°C. This product exhibits excellent mechanical stability and low fluid migration, with low evaporation at high temperatures.

A versatile tacky non-melting synthetic grease designed for use in automotive window regulator clutches requiring long service life, shear stability, and anti-wear properties as well as excellent rust and corrosion protection. Formulated with extreme pressure additives and PTFE for high load capability with an operating temperature range of -40°F(-40°C) to +350°F(177°C). Potential applications for this product include low speed roller bearings, plain bearings, gears, slides, cams and cables.

NS-62100-G, a member of Syn-Tech Ltd.'s Fluor-Tech PFPE grease and oil group, was designed to provide long life lubrication over an extremely wide temperature range of -65°C(-85°F) to 200°C(392°F). It is made with the highest quality PFPE base fluids which are chemically inert with most acids, fuels, and oxidizing agents. They do not emulsify with water and are resistant to all solvents except highly fluorinated solvents. Contains rust inhibiting, antiwear and EP additives for metal on metal applications. Extremely stable in the presence of oxygen. This product should not be mixed with hydrocarbon based lubricants. Before first use thoroughly purge all existing lubricants from bearings, gearboxes, switches, etc.

NS-62100-GUV if a UV tracer is required.
NS-62100-GL is available for reduced oil migration.

A PTFE fortified synthetic grease designed for use in applications requiring a long life, low oxidation rate lubricant that reduces friction and wear as well as providing damping and noise control. Formulated with extreme pressure and anti-wear additives along with excellent rust and corrosion protection, this product can be used in applications requiring both low and high temperature performance on ferrous and non-ferrous metals. Applications might include light duty gearboxes, bearings, cables, plastic gears, slides, etc.

NS-4318-G is a synthetic hydrocarbon based grease with a water washout resistant special calcium thickener. This product provides load carrying performance and reduced wear for steel and brass component. This grease also has excellent salt water corrosion protection and superior water washout and spray off properties for bearings and gears.

NS-4238-FG is a semi-synthetic PTFE enhanced specialty grease designed for exceptional noise and vibration damping characteristics. Suitable for open and closed gears, cables, slides and bearings. This product exhibits good oxidation stability and anti-wear properties.

A high capacity multi-fluid based grease designed for exceptional stability, mechanical lubricity and long life characteristics. This product exhibits excellent oxidation stability, anti-wear and extreme pressure properties. Suitable for gears, cables, slides and bearings.

NS-2196-G is a synthetic hydrocarbon grease designed for use on high contact force electrical contacts. It can also be used as a slide and bearing lubricant for metals and plastics. The incorporation of a non-melting thickener offers has a wide operating temperature range of -40°F (-40°C) to +300°F(+149°C). This product is fortified with additives to protect Cu and Cu alloys against corrosion and enhance oxidation stability. Potential applications might include switches, potentiometers, cables, light to medium load gear boxes and bearings.

A synthetic based grease with 'smooth feel', wide temperature range, thermal and mechanical stability. Designed to prevent wear and noise on automotive visor hinges.

NS-1822-G was formulated as a multi-purpose aircraft airframe grease for highly loaded bearings, gears and actuator screws. A low viscosity synthetic ester base fluid and a non-melting thickener system enable excellent low-temperature mobility and pumpability providing very low starting and running torque values. Good resistance to moisture as well as enhanced protection against both ferrous and non-ferrous metal rust and corrosion make this product a natural for use in marine environments.

NS-1822-G is a clay thickened grease approved under MIL-PRF-23827C Type II. NS-1822-G should not be mixed with soap based greases approved under MIL-PRF-23827C Type I

Medium viscosity EP/antiwear grease designed to be resistant to hexane solvent washout. It is not compatible with most mineral oil and synthetic greases. Non-melting thickener. NSF H1.

NS-1512-G is a synthetic hydrocarbon based general purpose anti-wear food grade grease. This product provides excellent antiwear resistance with an operating temperature range of -40°C to 149°C (-40°F to 300°F). Formulated with a water washout resistant aluminum complex thickener and additives for corrosion prevention for metals.
 

NS-1813-G is an NSF H-1 synthetic hydrocarbon grease for gears, bearings and slides. It's high temperature non-melting thickener, PAO base fluid and corrosion protection for ferrous and non-ferrous metals insures long life lubrication. Operating temperature range of -35°F to 300°F (shorter term usage at up to 375°F). Fortified for extreme pressure and antiwear additives for highly loaded applications.

NS-2110-F was formulated as an ISO 460 NSF H-1 food grade antiwear oil for gearboxes and chains. This product contains a unique blend of white mineral oil, synthetic base fluids and tackifier for high film strength and excellent oxidation resistance while protecting against rust and corrosion. This optimum blend of base oils possesses a higher viscosity index then straight white oil lubricants for better resistance to viscosity changes as temperatures increase.
 

NS-3110-680FG is a wide temperature range, food grade, synthetic gear and bearing oil. Formulated with high viscosity base oils for excellent shear stability unlike most high viscosity oils that are formulated with viscosity improvers that shear down and loose viscosity over time. Designed for EP/antiwear performance while protecting against rust.
 

NS-407-G is an NSF H-1 synthetic hydrocarbon grease for bearings and slides. It's non-melting thickener and corrosion protection for ferrous and non-ferrous metals insures long life lubrication. PTFE enhanced.

NS-62320-H was designed to lubricate at temperatures up to 275°C in applications requiring an NSF H1 approved grease for incidental food contact. It is made with the highest quality PFPE base fluids which are chemically inert with most acids, fuels, and oxidizing agents. They do not emulsify with water and are resistant to all solvents except highly fluorinated solvents. Protects ferrous metals against rust. Extremely stable in the presence of oxygen. This product should not be mixed with hydrocarbon based lubricants. Before first use thoroughly purge all existing lubricants from bearings, gearboxes, etc.

NS-10204-FG is a semi-fluid inorganic gelled synthetic hydrocarbon grease designed for use in slides and bearings requiring low drag lubrication with high viscometric stability, low evaporation and a wide operating temperature range. This product possesses high resistance to oxidation and moisture. Suitable for metal, plastic and rubber antiwear. Possible applications might include push-pull cables, bearings, gears and slides and other similar devices. Does not contain silicone fluid. NSF H-1 approved.
 

NS-4200-G was formulated to lubricate high and low current sliding electrical contacts. This product exhibits outstanding dry and high humidity nonferrous metal corrosion protection and an operating temperature range of -55°F(-67°C) to +225°F(107°C). It's soft consistency enables a constant lubricating film for high duty cycle switches. Applications include switch contacts and light duty mechanical interfaces.

A synthetic grease designed for use as a mechanical lubricant as well as an electrical contact interface lubricant. This product is suitable for low current (milliamp) and high current applications requiring low arcswitching debris, durability, and non-ferrous (e.g. Copper, Brass, Silver) corrosion protection over a range of -40°C to +149°C (-40°F to +300°F). NS-396-G exhibits excellent mechanical stability and low fluid migration with low evaporation at high temperatures. Lower mechanical friction and improved anti-wear at higher temperatures is also exhibited. May be used in switches, small gearboxes, wiper motors, cables and other similar devices.

Non-melting grease for high current switching with low arc debris. Inhibited for Cu
and Ag corrosion with good mechanical and chemical stability. Applications include
high current switches, potentiometers and similar devices.

High current switching with low arc debris. Inhibited for Cu and Ag corrosion with
enhanced contact antiwear. Also exhibits good mechanical and chemical stability.
Applications include high current switches, potentiometers and similar devices.

For on non-arcing, low current sliding switch contacts where a high quality, low volatility
and water washout resistant grease is required. Designed for applications that with
higher contact forces. Reduces wear due to vibration.

High grade PFPE grease. Low volatility and high oxidation resistance for extended durability
in thin films. Extremely wide operating temperature range. Contains an ultraviolet
reactive tracer.

For high current applications requiring extended operation at high temperatures, low arc
switching debris, reduced sliding wear and corrosion protection on Cu, Cu alloys, Ag,
Au and Ni metals. Excellent mechanical stability, low fluid migration, and low evaporation
at high temperatures. Good water resistance.

For high current applications requiring low arc switching debris, durability and corrosion
protection for Cu, Cu alloy, Ag, Au and Ni metals. Excellent mechanical stability,
low fluid migration, good mobility at low temperatures and low evaporation at high
temperatures. Applications include transmission neutral start switches and similar high
temperature, low current devices.

For low and high current applications with excellent protection against sliding contact
wear. Good protection against nonferrous metal corrosion due to humidity. Applications
include turn signal switches, window lift switches, power seat switches and ignition
switches.

NS-7502-GA is a non-hydrocarbon electrical contact lubricant designed to prevent contact wear and corrosion for contacts with higher then normal loading. This product has outstanding performance in applications requiring low arc-switching debris, durability, and lubricating qualities over a wide temperature range of -40°C to 140°C.  Inhibited for Cu and Ag corrosion, and exhibits good mechanical stability.

NS-4818-G is a ball and roller bearing grease formulated for continuous operation at temperatures above 150°C. Formulated with a per-fluorinated polyether (PFPE) base oil and a lithium complex soap thickerer to provide extreme pressure and antiwear protection as well as corrosion resistance under extreme operating conditions.

A high capacity multi-fluid based grease designed for exceptional stability, mechanical lubricity and long life characteristics. This product exhibits excellent oxidation stability, anti-wear and extreme pressure properties. Suitable for gears, cables, slides and bearings.

NS-407-G is an NSF H-1 synthetic hydrocarbon grease for bearings and slides. It's non-melting thickener and corrosion protection for ferrous and non-ferrous metals insures long life lubrication. PTFE enhanced.

A PTFE fortified synthetic grease designed for use in applications requiring a long life, low oxidation rate lubricant that reduces friction and wear as well as providing damping and noise control. Formulated with extreme pressure and anti-wear additives along with excellent rust and corrosion protection, this product can be used in applications requiring both low and high temperature performance on ferrous and non-ferrous metals. Applications might include light duty gearboxes, bearings, cables, plastic gears, slides, etc.

An EP/antiwear fluid grease with extremely low oil separation for use in gearboxes with marginal seals. This product is formulated with a unique thickener that flows like an oil but resists leaking out of poor case seals on gearboxes originally designed for greases. For use on steel, bronze or plastic gears. Excellent lubrication for worm gears.

A special purpose grease, designed for use on metal to metal interfaces requiring a long service life, stability and anti-wear properties as well as excellent rust and corrosion protection. Formulated with extreme pressure additives for high load capabilities. This product offers an operating temperature range of -40°F to +300°F. The combination of high temperature base fluid and thickener will lubricate a wide range of applications including gearboxes, gear couplings, cams, wheel bearings and drive shafts.

NS-3913-G is the only lubricant approved for use on Kop-Flex® high PV gear shaft couplings.

Designed for use in pneumatic actuator seals requiring low drag lubrication and dynamic sealing with good moisture resistance. NS-5606-G conditions elastomer seals to prevent hardening. This product is fortified with corrosion protection additives for ferrous and non-ferrous metals It also contains friction modifiers, including PTFE. NS-5606-G is an good lubricant for metal on plastics and elastomersas well as lightly loaded metal on metal applications. Other possible applications might include push-pull and rotating drive cables, bearings, plastic on metal gears, slides and other similar devices.

A non-melting semi-synthetic high performance grease formulated for extreme pressure, anti-wear, and noise control properties. High stability, low migration, wide temperature range, and excellent load capability for use on gears, chains, bearings and cables. Excellent anti-wear for metal to metal and plastics to metals. Additionally, this product exhibits corrosion protection and high oxidation stability. NS-8301-G should not be mixed with lithium soap greases. Before first use thoroughly purge all existing lubricants from bearings, gearboxes, etc.

Provides long life lubrication over an wide operating temperature range. Made with the highest quality PFPE base fluids which are chemically inert with most acids, fuels, and oxidizing agents. Will not emulsify with water and is resistant to all solvents except highly fluorinated solvents. Contains rust inhibiting, antiwear and EP additives for metal on metal applications. Extremely stable in the presence of oxygen.

NS-6617-SBO is a unique combination of a medium viscosity synthetic hydrocarbon oil in a solid porous polymer carrier formulated to lubricate ball, tapered roller, needle roller, spherical roller and cylindrical roller bearings. The porous polymer carrier slowly releases oil to the bearing components. The carrier also forms a wall, blocking particulate contaminantion without the need for expensive seals. This product provides protection from rust and corrosion. It also exihibits enhanced antiwear and extreme pressure protection for ferrous metals.

Usage instructions: Mix NS-6617-SBO to disperse polymer particles that may have settled. The solid polymer gell matrix is formed after heating the bearing with NS-6617-SBO to 145°C or greater for at least 30 minutes. Allow the bearing to cool to room temperature before operating.

A unique combination of an ISO 100 synthetic hydrocarbon oil in a solid porous polymer carrier formulated to lubricate ball, tapered roller, needle roller, spherical roller and cylindrical roller bearings. The porous polymer carrier slowly releases oil to the bearing components. The carrier also forms a wall, blocking particular contaminants without the need for expensive seals. The solid polymer gell matrix is formed after heating the bearing with NS-1018-SBO to 145°C or greater for 30 minutes.

NS-2517-SBO is a unique combination of an ISO 100 synthetic hydrocarbon oil in a solid porous polymer carrier formulated to lubricate ball, tapered roller, needle roller, spherical roller and cylindrical roller bearings. The porous polymer carrier slowly releases oil to the bearing components. The carrier also forms a wall, blocking particulate contaminantion without the need for expensive seals.

Usage instructions: Mix NS-2517-SBO to disperse polymer particles that may have settled. The solid polymer gell matrix is formed after heating the bearing with NS-2517-SBO to 140°C or greater for at least 30 minutes. Allow the bearing to cool to room temperature before operating.

NS-4318-G is a synthetic hydrocarbon based grease with a water washout resistant special calcium thickener. This product provides load carrying performance and reduced wear for steel and brass component. This grease also has excellent salt water corrosion protection and superior water washout and spray off properties for bearings and gears.

NS-4238-FG is a semi-synthetic PTFE enhanced specialty grease designed for exceptional noise and vibration damping characteristics. Suitable for open and closed gears, cables, slides and bearings. This product exhibits good oxidation stability and anti-wear properties.

NS-2609-G is a synthetic hybrid grease with a solid additive package formulated to prevent wear and resist water washout. Gelled with a lithium complex soap thickener for high shear stability. Protects steel from rust and yellow metals from corrosion.

NS-1822-G was formulated as a multi-purpose aircraft airframe grease for highly loaded bearings, gears and actuator screws. A low viscosity synthetic ester base fluid and a non-melting thickener system enable excellent low-temperature mobility and pumpability providing very low starting and running torque values. Good resistance to moisture as well as enhanced protection against both ferrous and non-ferrous metal rust and corrosion make this product a natural for use in marine environments.

NS-1822-G is a clay thickened grease approved under MIL-PRF-23827C Type II. NS-1822-G should not be mixed with soap based greases approved under MIL-PRF-23827C Type I

NS-1514-G is a food grade synthetic hydrocarbon based grease with a calcium sulfonate complex thickener. This product provides load carrying performance and reduced component wear. This grease also has excellent corrosion protection and superior water washout and spray off properties for bearings and gears.
 

A fully synthetic NLGI 2 grease formulated to provide friction reduction, antiwear and mild EP protection with premium corrosion protection for gears and bearings. A high viscosity index PAO base fluid provides low drag lubrication at lower operating temperatures. Its shear resistant calcium sulfonate complex thickener system provides a consistent lubrication film and is extremely resistant to moisture, humidity and steam.

A water resistant fluid grease formulated to lubricate retractable marine antennas.
 

NS-4318-G is a synthetic hydrocarbon based grease with a water washout resistant special calcium thickener. This product provides load carrying performance and reduced wear for steel and brass component. This grease also has excellent salt water corrosion protection and superior water washout and spray off properties for bearings and gears.

High grade PFPE grease. Low volatility and high oxidation resistance for extended durability
in thin films. Extremely wide operating temperature range. Contains an ultraviolet
reactive tracer.

NS-1822-G was formulated as a multi-purpose aircraft airframe grease for highly loaded bearings, gears and actuator screws. A low viscosity synthetic ester base fluid and a non-melting thickener system enable excellent low-temperature mobility and pumpability providing very low starting and running torque values. Good resistance to moisture as well as enhanced protection against both ferrous and non-ferrous metal rust and corrosion make this product a natural for use in marine environments.

NS-1822-G is a clay thickened grease approved under MIL-PRF-23827C Type II. NS-1822-G should not be mixed with soap based greases approved under MIL-PRF-23827C Type I

Provides long life lubrication over an wide operating temperature range. Made with the highest quality PFPE base fluids which are chemically inert with most acids, fuels, and oxidizing agents. Will not emulsify with water and is resistant to all solvents except highly fluorinated solvents. Contains rust inhibiting, antiwear and EP additives for metal on metal applications. Extremely stable in the presence of oxygen.

A high performance, semi-fluid, low capillary grease formulated for high cling, anti-wear qualities as well as damping and noise control properties. High stability, low migration, wide temperature range, and good load capability allow use in gear boxes, cables and mechanisms. Excellent anti-wear for metal to metal and plastics to metals. This product also exhibits high oxidation stability.
 

NS-62320-H was designed to lubricate at temperatures up to 275°C in applications requiring an NSF H1 approved grease for incidental food contact. It is made with the highest quality PFPE base fluids which are chemically inert with most acids, fuels, and oxidizing agents. They do not emulsify with water and are resistant to all solvents except highly fluorinated solvents. Protects ferrous metals against rust. Extremely stable in the presence of oxygen. This product should not be mixed with hydrocarbon based lubricants. Before first use thoroughly purge all existing lubricants from bearings, gearboxes, etc.

NS-407-G is an NSF H-1 synthetic hydrocarbon grease for bearings and slides. It's non-melting thickener and corrosion protection for ferrous and non-ferrous metals insures long life lubrication. PTFE enhanced.

For low and high current applications with excellent protection against sliding contact
wear. Good protection against nonferrous metal corrosion due to humidity. Applications
include turn signal switches, window lift switches, power seat switches and ignition
switches.

For high current applications requiring low arc switching debris, durability and corrosion
protection for Cu, Cu alloy, Ag, Au and Ni metals. Excellent mechanical stability,
low fluid migration, good mobility at low temperatures and low evaporation at high
temperatures. Applications include transmission neutral start switches and similar high
temperature, low current devices.

For high current applications requiring extended operation at high temperatures, low arc
switching debris, reduced sliding wear and corrosion protection on Cu, Cu alloys, Ag,
Au and Ni metals. Excellent mechanical stability, low fluid migration, and low evaporation
at high temperatures. Good water resistance.

High grade PFPE grease. Low volatility and high oxidation resistance for extended durability
in thin films. Extremely wide operating temperature range. Contains an ultraviolet
reactive tracer.

For on non-arcing, low current sliding switch contacts where a high quality, low volatility
and water washout resistant grease is required. Designed for applications that with
higher contact forces. Reduces wear due to vibration.

High current switching with low arc debris. Inhibited for Cu and Ag corrosion with
enhanced contact antiwear. Also exhibits good mechanical and chemical stability.
Applications include high current switches, potentiometers and similar devices.

Non-melting grease for high current switching with low arc debris. Inhibited for Cu
and Ag corrosion with good mechanical and chemical stability. Applications include
high current switches, potentiometers and similar devices.

NS-1302-G was designed to provide smooth feel to plastic-plastic and plastic-metal sliding interfaces. The use of a high performance viscosity modifier combined with a low viscosity base fluid allows for excellent low temperature use with good high temperature damping ability. This product exhibits excellent mechanical stability and extremely low fluid migration, with low evaporation at high temperatures. Lower mechanical friction and improved anti-wear at higher temperatures are also exhibited. May be used in mechanical sections of switches, small gearboxes, wiper motors, cables and other similar devices.

A synthetic grease designed for use as a mechanical lubricant as well as an electrical contact interface lubricant. This product is suitable for low current (milliamp) and high current applications requiring low arcswitching debris, durability, and non-ferrous (e.g. Copper, Brass, Silver) corrosion protection over a range of -40°C to +149°C (-40°F to +300°F). NS-396-G exhibits excellent mechanical stability and low fluid migration with low evaporation at high temperatures. Lower mechanical friction and improved anti-wear at higher temperatures is also exhibited. May be used in switches, small gearboxes, wiper motors, cables and other similar devices.

A fully synthetic NLGI 2 grease formulated to provide friction reduction, antiwear and mild EP protection with premium corrosion protection for gears and bearings. A high viscosity index PAO base fluid provides low drag lubrication at lower operating temperatures. Its shear resistant calcium sulfonate complex thickener system provides a consistent lubrication film and is extremely resistant to moisture, humidity and steam.

A silicone based fluid grease. Maintains a moisture resistant film for long life lubrication of control cables.
 

An environmentally friendly grease for elastomer bushings. Eliminates squeeking while reducing friction and wear. Waster resistant.
 

Syn-Tech "Boardoil" was developed as a premium ball and roller bearing oil for long boards and skates. Unlike most synthetic oils sold for board and skate bearings, this product is formulated with a unique componant designed to "wet out" the bearing ring, balls and seals with a low viscosity synthetic hybrid fluid film that protects against bearing wear due to extreme pressure. It also protects against bearing rust and pitting for a smoother ride. This product also contains a light tackifier to keep the oil in place.
 

NS-1514-G is a food grade synthetic hydrocarbon based grease with a calcium sulfonate complex thickener. This product provides load carrying performance and reduced component wear. This grease also has excellent corrosion protection and superior water washout and spray off properties for bearings and gears.
 

NS-1822-G was formulated as a multi-purpose aircraft airframe grease for highly loaded bearings, gears and actuator screws. A low viscosity synthetic ester base fluid and a non-melting thickener system enable excellent low-temperature mobility and pumpability providing very low starting and running torque values. Good resistance to moisture as well as enhanced protection against both ferrous and non-ferrous metal rust and corrosion make this product a natural for use in marine environments.

NS-1822-G is a clay thickened grease approved under MIL-PRF-23827C Type II. NS-1822-G should not be mixed with soap based greases approved under MIL-PRF-23827C Type I